Jobs

Current Job Openings at Amaiden Energy Nigeria Limited, 29th October, 2019


Amaiden Energy Nigeria Limited, (formerly Moody International Nigeria Limited) was established in 1996 as a partnership between Moody International Group and Nigerian investors. Since commencing operations in March 1997 the company continues to grow and exerts its presence in numerous Projects in the Nigeria Oil and Gas Industry. We are recruiting to fill the position below:   Job Title: Cathodic Protection /Corrosion Control Inspector Location: Nigeria Job Type: Contracts Description

  • Provide continuous guidance to the contractor on corrosion control/protection and cathodic protection (CP) of equipment, pipe, and structure.
  • Ensures that the quality of construction activities in area of expertise (discipline), requirements together with national and international standards to cathodic protection requirement, are properly fitted on the protected side of structure.
  • Record On/Off Cathodic Protection Potential of Buried lines, Measure current drain at a junction box.
  • Close interval potential survey(CIPS) on buried line, evaluate report issue Potential gradient reports.
  • Supervise corrosion controls activities, such as cathodic protection deep well installation, coatings during construction, etc for the pipeline assets.
  • Develop and publish weekly/monthly progress report, review project and work related documents and/or findings for analysis and strategy reports.
  • Perform duties involved with installation, testing, and evaluation of cathodic protection systems and identify potential areas of concern including assisting.
  • Supervise coating survey by Direct current voltage gradient (DCVG), able to supervise Overline potential measurement.
  • Report technical change requirements (MoC)/non-conformance and schedule deviation, participate in in-line inspections and corrosion management.
  • Run a holiday inspection of Coated structures.
  • Trouble shoot cathodic protection Ground bed, perform Ground bed failure test and carry out cable continuity test.
  • Record Transformer rectifier output from the Voltmeter and Ammeter and Measure Voltage and Current across the Rectifier terminals to confirm reading from Ammeter and Voltmeter, do a general Transformer rectifier checks.
  • Record Cathodic protection (CP) output at the junction boxes and Test post/Interference bond stations.
  • Witness or perform Cathodic protection interference Investigation from third party pipeline.
  • Perform current demand calculation and do a preliminary design to determine anodes requirement.
  • Troubleshoot to determine reason for Cathodic protection outage.
  • Carry out Cathodic Protection Solar station availability check and record anomalies.
  • Review cathodic protection requirements, corrosion mitigation and monitoring activities in the field to identify needed system modifications or procedural changes.
  • Perform ultrasonic wall thickness inspection to determine area with wall loss due to corrosion activities.
  • Supervise Deep well and convectional Ground bed installation and commissioning.
  • Perform other tasks as may be assigned by COMPANY
Job Requirements
  • HND or B.Sc /B.Eng in Mechanical/Chemical Engineering , Industrial Chemistry, Electrical Engineering
  • Professional Experience (number of years):5-years and above of experience in Cathodic Protection Inspection with Project background within Oil & Gas industry. Experience on construction and maintenance works in corrosion field
  • The personnel shall be qualified in line with EN15257:2006 and ISO 15257:2017 requirements
  • National association of corrosion Engineer 1 (NACE Level1) on Cathodic Protection Tester (CPT),
  • NACE Basic Corrosion Certificate,
  • Direct Current Voltage Gradient Certificate (DCVG),
  • Member of Association of non-destructive Testing (ASNT) Level1,
  • Pulse eddy current inspection certificate.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: NDT Level II Inspector Location: Nigeria Category: Others Job Type: Contracts Job Nature: Resident Description
  • Ensure that set-up and calibration of non-destructive testing equipment are up to date and valid to perform the required tests
  • Ensure and establish techniques for proper examination of objects under inspection are in line with strict adherence to both safety and required regulations
  • Establish the testing criteria in accordance with applicable specifications or standards and evaluate results accordingly,
  • Fill out required logs and statistical data sheets as required
  • Produce concise written NDT reports
  • Report to COMPANY QAQC Lead
  • Perform other jobs related task assigned by management
  • Apply testing criteria and Interpret or evaluate test results in accordance with applicable codes, standards, specifications, or procedures
  • Interpret the results of all methods of non-destructive testing (NDT) such as acoustic emission, electromagnetic, leak, liquid penetrant, magnetic particle, neutron radiographic, radiographic, ultrasonic, vibration analysis, and visual testing
  • Able to read and interpret blueprint and engineering drawings and able to document non-conformances as required
  • Supervise NDT Level I Inspectors.
Job Requirements Minimum Qualifications:
  • HND or Degree – Mechanical or Metallurgical Engineering or related Engineering Discipline
  • Professional Experience (number of years): 10-years and above in Oil & Gas Industry.
  • Must have knowledge of applicable codes and standards of AWS, ASME, API
Minimum Professional Certification(S):
  • NDT Level II Certification ASNT Level II in RT VT, UT, MT, PT etc
  • Ability to communicate well at all levels within the Company and work under pressure as project demand
  • Ability to follow instructions and procedures
  • Ability to interpret results of the inspections
  • Ability to analyze inspection data trends and make recommendation for inspection level and frequency changes.
  • Good Physical Condition, requires walking, climbing, and tolerance to environmental conditions
  • Must be proficient in common PC software (MS Word; MS Excel; MS Outlook; etc
  • Fluency in English and ability to communicate in equipment supplier’s language.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: NDT Level III Inspector Location: Nigeria Category: Others Job Type: Contracts Description
  • Interface with construction and engineering team regarding technical and field production issues
  • Interface with contractor representatives for relevant quality/technical issues and ensure smooth resolutions afterwards,
  • He / She has technical responsibility for Level II NDT Technicians for all the NDE
  • Ensure that the field production facilities test concise written NDT reports
  • Report to Seplat QAQC Lead
  • Interpret codes, standards, and other contractual documents that control the examination methods to meet industry and customer requirements and endorse accordingly
  • Prepare and approve NDT procedures and other related NDT work instructions
  • Conduct training and examination of NDT personnel (where necessary)
  • Supervise NDT Level I & II Inspector.
Job Requirements Minimum Qualifications:
  • HND or Degree – Mechanical or Metallurgical Engineering or related Engineering Discipline
  • Professional Experience (number of years): 15-years and above in Oil & Gas Industry.
  • Must have knowledge of applicable codes and standards of AWS, ASME, API.
Minimum Professional Certification:
  • NDT Level II Certification ASNT Level III in RT VT, UT, MT, PT etc.
General Requirements:
  • Ability to communicate well at all levels within the Company and work under pressure as project demand
  • Prepare instructions, procedures as well as ability to interpret results of the inspections
  • Ability to analyze Level II inspection data trends and make recommendation for inspection level and frequency changes.
  • Good Physical Condition, requires walking, climbing, and tolerance to environmental conditions
  • Must be proficient in common PC software (MS Word; MS Excel; MS Outlook; etc
  • Fluency in English and ability to communicate in equipment supplier’s language.
How to Apply Interested and qualified candidates should: Click here to apply online Job Title: Painting / Coating Inspector Location: Nigeria Job Type: Contracts Job Nature: Resident Description
  • Review the ITP and provide assurance/control of the quality of the paint codes, visual inspection, mixing and its application
  • Conduct a pre-mob inspections on materials (Paint, thinner, abrasive materials and other consumables etc) and Equipment (Blasting air compressor, nozzles, scaffolds, Airless /Conventional Spraying machines, Holiday detector, spraying tip, Deadman handle).
  • Issues the relevant quality control records and, when necessary, report and send to Quality Control Supervisor non-conformances reports (as applicable),
  • Provide unbiased reports and a third party (manufacturer) paint inspection,
  • Ensure environment for paint storage is in line with requirement and certification of paint consumables are valid and update to date.
  • Performs qualifications of coating processes and notify the Project Quality Lead and Contractor of any anomalies or irregularities in the specifications as Non-conformance products,
  • Review relevant areas in scope of work and conduct receiving inspection with paint contractor prior to surface preparation and paint application,
  • Confirm that surface preparation is in line with acceptable requirements prior to application and report same immediately.
  • Always ensure, confirm and records atmospheric conditions prior to starting of any painting operations.
  • Carries out wet and dry film thickness checks upon completion of pain application.
  • Verifies the correct Colour-coding and painting during painting to ensure that COMPANY colour coding scheme is duly maintained
  • Performs visuals inspections of determine paint condition, corrosion status of existing surface
  • Perform cathodic dis-bondment test after coating
  • Performs penetration testing.
  • Evaluates impact testing.
  • Performs visual checks after blasting.
  • Verify and ensure measure surface area of structures to be coated/painted is line with the agreed surface area in the contract
  • Estimate quantity of paint to applied on estimated surface
  • Check application of Fusion bonded epoxy and Polyethylene coating in coating plant mostly for line pipes.
Job Requirements Minimum Qualification:
  • HND or BSc /B.Eng Degree – Metallurgy & Materials/ Chemical Engineering, Industrial Chemistry
  • Professional Experience (number of years): Minimum of Five (5) years and above of experience in Coating and Painting inspection, with project background within Oil & Gas industry.
  • Experience on construction and maintenance works in corrosion field
Minimum Professional Certification(s):
  • Member & Certified to National association of corrosion Engineer (NACE Level I or II) on coating inspector program (CIP-1),
  • Very conversant with Steel Structures Painting Council (SSPC) on Painting/Coating,
  • NACE Basic Corrosion Certificate,
General Requirements:
  • A self-starter with less supervision on what to do
  • Ability to interpret Code and standards accordingly and apply them,
  • Ability to estimate quantity requirements for proper coverage from drawings and COMPANY specifications
  • Knowledge of proper handling, transporting and storing requirements for protective coating and related materials,
  • Ability to communicate well at all levels within the Company.
  • Ability to analyze Steel surface and paint condition and make recommendation from inspection level.
  • Good Physical Condition, requires walking, climbing, and tolerance to environmental conditions
  • Must be proficient in common PC software (MS Word; MS Excel; MS Outlook; etc)
  • Fluency in English and ability to communicate in equipment supplier’s language
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Instrument QA / QC Inspector Location: Nigeria Job Type: Contracts Description
  • Provide expertise to site team to avoid/resolve quality issues relating to Instrument/control work.
  • Provide early warning of potential quality issues and ensure non-conformances are identified and reported to COMPANY through regular review, follow-up on corrective actions and update of QA/QC status.
  • Review COMPANY packages, Contractor procedures, Inspection and Test Plans (ITPs) and other technical and quality documents as required. Ensures that all testing requirements identified in COMPANY specifications are addressed by construction Contractor or supplier.
  • Verify that all testing procedures have been approved and are on site. Confirm testing parameters are duly recorded and testing equipment are calibrated.
  • Review and witness hold point inspection during construction in accordance with standard requirement.
  • Verify that all Instrumentation & Control systems are built in accordance with the design.
  • Carry out visual inspection of the Instrumentation & Control modules for overall assembly and installation progress.
  • Inspection of cables and cable tray installations, internal & external, junction boxes and panels; inspection of power and control cables installation to ensure compliance with the applicable codes and standar
  • Inspection of HVAC systems and ducting installations.
  • Operate inspection/test equipment and record/download inspection data.
  • Attend and witness testing associated with Instrumentation & Control equipment and systems e.g Functional test and other Instrumentation & Control QAQC activities as designated on the Inspection Test Plan for the project.
  • Assist in Verification, Monitoring and Close-out of Punch List items;
  • Perform quality audit (spot checks) to verify work activities are in compliance with approved Quality procedures.
  • Represent Company and Service Contractor in a positive and professional manner.
  • Review specifications and work procedures to ensure ITPs comply with Company r
  • Witness system FAT and SAT as may be required.
  • Ensure Contractor’s documentation conform and are compiled progressively as
  • Carry out daily surveillance reporting and submission of weekly report of Contractor’s work.
  • Provide general QA/QC direction to Company on QA/QC related
Job Requirements
  • HND or Degree in Electrical or Instrumentation & Control Engineering
  • 10 years and above of experience in Instrumentation & Control inspection with Project background within Oil & Gas industry.
  • Construction experience is required on Instrumentation & Control installations. Experience on construction yard in Construction Contractor team is required.  Proficiency in using Microsoft Office Suite (Word, Excel and Outlook).
  • Must have knowledge of applicable Local and International Codes and Standards (e.g. IEC, NFPA, UL, BS et), as applicable in the oil/gas industry.
  • Good understanding of design of Instrumentation & Control systems of oil and gas processing facilities
  • MNSE, MNIEEE or MIEEE; COREN (Added advantage)
  • Very conversant with BS, IEC, ISO, API and other codes and standards relating to Instrumentation/controls
  • International Certifications - QA/QC, CEI, etc.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Safety Inspector / Officer Location: Nigeria Job Type: Contracts Job Nature: Resident Description
  • Keep workers, supervisors and the entire workforce informed about HSE Management system often
  • Attend morning field safety briefings at staging areas and assembly points to ensure site safety plan was covered
Job Requirement
  • University degree or a higher National Diploma in Engineering or sciences
  • Minimum of 15 years in the Upstream Oil and Gas industry, with at least 8 years in a similar position
  • Job holders must have NEBOSH and very conversant with Oil & Gas Occupational Health, Safety and Environmental requirements as added advantage
  • Experience with facilitating efforts to resolve interface issues and coordinate multipart HSE objectives,
  • Member of relevant professional institutions
  • Proficient in MS applications e.g Word/Excel/PowerPoint
How to Apply Interested and qualified candidates should: Click here to apply online  
Job Title: Access Controller Location: Nigeria Job Type: Contracts Description
  • Control access to Project site facilities and properties, protect life, maintain order, resist criminal attacks against AGPC personnel, visitors and contractors,
  • Resist any other form of violent attacks against any project personnel including intruders
  • He/she must also be familiar with AGPP emergency notification system, communication system and post emergency action plans,
  • He/she will maintain in a neat, orderly, legible fashion, all logbooks, ledgers, record books, incident reports, or any other written record of duties performed or of any security event.
  • He/she will not be compromised by providing information about AGPC personnel or facilities to anyone without the specific approval of the project
  • Identify and make the proper log entries for visitors and other appropriate persons to AGPP project site or facilities.
  • Access Controller must be able to demonstrate a working knowledge of the technical security systems and access control devices maintained in duty post.
  • Must be able to demonstrate a working knowledge of the post's emergency action plans (fire, bomb, intruder, etc.).
  • He/she must be able to identify and issue appropriate access control identification badges according to AGPP policies
Job Requirements
  • HND or B.Sc in Social Science
  • Local experience and strategic thinker,
  • Experience in penetration test and detection
  • Sound judgement and initiative.
  • A professional and mature approach
  • A high level of courtesy
How to Apply Interested and qualified candidates should: Click here to apply online
  Job Title: Pipeline QAQC Inspector Location: Nigeria Job Type: Contracts Job Nature: Resident Description
  • Responsible for inspecting and ensuring that the Company's Pipeline construction and pipeline repair projects adhere to the Project Procedure / Work Plan, industry standard, company’s safety standards, as well as all state and federal regulations.
  • Provide early warning of potential quality issues and ensure non-conformances are identified and reported to COMPANY through regular review, follow-up on corrective actions and update of QA/QC status.
  • Review COMPANY packages, Contractor procedures, Inspection and Test Plans (ITPs) and other technical and quality documents as required. Ensures that all testing requirements identified in COMPANY specifications are addressed by construction Contractor or supplier.
  • Verify that all testing procedures have been approved and are on site. Confirm testing parameters are duly recorded and testing equipment are calibrated.
  • Support inspection of materials and review of material certification prior to use
  • Verify depth and alignment of trenches, using tape measure and examines bottom of trench for rocks or other hard objects that might damage pipe coatings.
  • Examines surface and x-ray films of welded joints to detect external and internal welding defects.
  • Responsible for selection of welds for non-destructive testing as well as recording and listing of defective welds.
  • Observe coating and wrapping of pipe or pipe joints for conformance to specifications and verify accuracy of coating by observing or conducting electrical tests for holidays.
  • Carry out audit of the approved Third Party NDT Inspection Company.
  • Review the inspection and testing methods and procedures for Radiographic, Dye Penetrant, Magnetic Particle, and Ultrasonic Inspections.
  • Supervise and pre-qualify all crews/workers engaged in Welding Operations by conducting welder qualifications testing and procedures qualification testing.
  • Review of hydrostatic test packages for NDT compliance prior to testing, and overseeing hydro pressure testing of pipelines.
  • Monitor any Post Weld Heat Treatment on site and review the completed test reporting.
  • Actively monitor site radiation safety and review day to day applications for x-raying of welds.
  • Ensure that welding parameters and pre-heat conditions are maintained according to the specifications and procedure qualifications.
  • Ensure welding standards are observed and maintained at all stages of pipeline construction.
  • Represent Company and Service Contractor in a positive and professional manner.
  • Review specifications and work procedures to ensure contractor comply with Company requirements.
  • Ensure Contractor’s documentation are acceptable and are compiled progressively as required.
  • Carry out daily surveillance reporting and submission of weekly report of Contractor’s work.
  • Provide general QA/QC direction to Company on QA/QC related issues.
  • Perform other tasks as may be assigned by COMPANY
Job Requirements Minimum Qualification:
  • HND or Degree – Mechanical Engineering.
  • Professional Experience: 10-years and above of experience in Pipeline with Project background within Oil & Gas industry. Construction experience is required on pipeline installations. Experience on construction yard in Construction Contractor team is required.  Proficiency in using Microsoft Office Suite (Word, Excel and Outlook).
  • Must have knowledge of applicable Local and International Codes and Standards (e.g. API 1104, CSWIP, ASME B31.4 and ASME B31.8), as applicable in the oil/gas
  • Good understanding of design of Pipeline systems of oil and gas processing
Minimum Professional Certification(s):
  • MNSE, COREN (Added advantage);
  • Others: International Certifications, etc.
General Requirements:
  • Ability to communicate well in verbal and written English at all levels within the Company.
  • Good team player with interpersonal skills and aptitude to work in a diverse cultural
  • Ability to analyze inspection data trends and make recommendation for inspection level and frequency changes.
  • Good physical condition, requires walking, climbing, and tolerance to environmental conditions.
  • Understand and apply quality management principles and processes
How to Apply Interested and qualified candidates should: Click here to apply online  
Job Title: Process Vessel / Static Inspector Location: Nigeria Job Type: Contracts Job Nature: Resident Description
  • Review the ITP and provide assurance/control of the quality of the static and other process equipment/vessels
  • Inspect drawings, designs and specifications for piping, boilers and other vessels meant for the COMPANY use
  • Witness Procedure Qualification Test and welding procedure specification in line with API, ANSI, ASME, AWS and BS standards (as applicable).
  • Witness and interpret x-ray of welds, and revalidate the ultrasonic, magnetic particle, or dye penetrating tests on welds by the contractors.
  • Ability to read drawings, material take-off and identify materials on site. Experience with pneumatic and electrical instrumentation commonly found in oil and gas operations.
  • Conduct physical inspection requiring Contractor vessels and heat exchangers in-fabrication activities.
  • Carry out in-situ inspection and maintenance of vessels and associated piping for existing facilities and make recommendation accordingly.
  • Review and monitor the hydrostatic test procedure for vessels and piping work and prepare report accordingly.
  • Experience with hazardous area classifications and with restrictions imposed by such classifications on work practices both onshore and offshore.
  • Act as company representative in supervising, directing and participating in project construction, maintenance or vessel preparation for inspection.
  • Witness fabrication as well as installation activities and prepare inspection reports
  • Carry out a spot checks on site prior to shop or field fabrication and encourage a safe working environment at all time.
Job Requirements Minimum Qualification:
  • HND or BSc /B.Eng Degree – Metallurgy & Materials / Chemical Engineering,
  • Professional Experience (number of years): Minimum of Fifteen (15) years and above
  • Experienced as a vessel or piping inspector plus five (10) years working experience in vessel Inspection & certification.
  • Good knowledge or certification in API -510 (Pressure Vessel Inspector); API 570 (Piping Inspector) and API 653 (Tank Inspector)
  • Experience on construction and Inspection of Process Vessels/static equipment
Minimum Professional Certification(s):
  • Member Nigerian Society of Engineers & COREN as well as other international professional bodies,
  • Very conversant with API, ANSI, ASME, AWS and ASTM Standards,
  • Basic knowledge of work process with a company with ASME “U” & “R” Stamp effectively,
General Requirement:
  • A self-Started with less supervision on what to do
  • Experience in providing recommendation and supervision of maintenance, repair or replacement of vessels and associated piping inclusive of separators and storage vessels,
  • Knowledge of heat treatment and reaction of materials relating to ASME- P classification of materials
  • Ability to estimate quantity requirements for proper coverage from drawings and COMPANY specifications
  • Knowledge of proper handling, transporting and storing requirements for protective coating and related materials,
  • Ability to communicate well at all levels within the Company.
  • Ability to weld map of the vessel and analyze the entire weld history and make recommendation to proceed to next step or otherwise.
  • Good physical condition, requires walking, climbing, and tolerance to environmental conditions
  • Fluency in English and ability to communicate in equipment supplier’s language.
How to Apply Interested and qualified candidates should: Click here to apply online
  Job Title: Lifting Equipment and Accessories Inspector Location: Nigeria Job Type: Contracts Description
  • Conduct in-service inspection schedule including color coding, repairs and load testing for all the lifting gears for the project
  • Responsible for the maintenance of assigned lifting equipment and accessories dedicated to the project
  • Ensure that the material used and force influences in lifting equipment and gears are adequate
  • Ensure the adequate management and proper storage of wire rope by checking for flexibility, fatigue, wear, abrasion, rotation and elongation,
  • Testing and Certification work on all Lifting Equipment Plant and Machinery,
  • Advise contractors riggers on the project on the needs for safety awareness
  • Advice of different types of Cranes, Passenger lifts and Escalators, Goods Lifts, Fork Lift Trucks, MEWPS and Cherry Pickers, Lifting Structures, Anchorage Points, Lifting Beams etc as may be required.
  • Verify Load monitoring equipment.
  • Provide Proof Load and initial testing such as bolt torque checks.
  • Periodic inspection on all cranes and lifting equipment, this includes but is not limited to drilling equipment & tools, pedestal and overhead cranes, ROV/Dive spreads, fixed lifting equipment, lifeboats and life raft launch and recovery systems and loose lifting equipment.
  • Make use of contractors and ensure their compliance with Company requirements
Job Requirements
  • HND or B.Sc in Engineering or Science
  • Member of Lifting Equipment Engineers Association
  • 5-10 year working experience in similar role
  • Lifting and Hoisting Training & Certification
  • HSE Level III Certification
  • Journey Management Training & Certification on lifting inspection.
  • Conversant with Lifting Operations and Lifting Equipment (LOLER), PUWER and Occupational Health & Safety at Work.
  • Good knowledge of DIN 15030 (Lifting Equipment; Acceptance Testing of Crane Installations; Principles); NORSOK R-002 (Lifting Equipment); DIN 15400 (Lifting hooks: materials, mechanicals, mechanical properties, Lifting capacity and stresses.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Multi-Discipline QA/QC Engineer Location: Nigeria Category: Others Job Type: Contracts Job Nature: Resident Description
  • Review the ITPs and provide quality assurance/control on the aspect of the activities in question and provide recommendation accordingly
  • Review and interpret all the relevant codes and standards accordingly as its affect the project execution plan,
  • Participate in conduct of pre-mob inspections on project resources (materials and equipment) and make recommendation accordingly
  • General knowledge of the total scope of project work and functions of all the various inspection requirements and plan with the COMPANY QA/QC Lead.
  • Conduct spot check/assessment on all the project contractors and prepare report with recommendations
  • Analyze all the project Non-conformance, Audit findings and improvement suggestions and ensure timely closure of any outstanding
  • Review all report generated by the inspectors and collate them for COMPANY QA/QC Lead for subsequent actions.
  • Build good relationship between all the Inspectors and ensure timely delivery of discipline reports on weekly basis or as project demand.
  • Develop project specific assessment and conduct these site assessments accordingly.
Job Requirements Minimum Qualifications:
  • HND or BSc /B.Eng Degree - Engineering
  • Professional Experience (number of years): Minimum of Fifteen (15) years and above in EPCIC project Execution, with sound project background within Oil & Gas industry.
  • Lead Auditor in ISO 9001:2008 or preferably ISO 9001:2015
  • Experience on Engineering and construction as well as maintenance works in oil & gas field.
Minimum Professional Certification(S):
  • Member Nigerian Society of Engineer or COREN and other international bodies,
  • Sound knowledge in Engineering Design, Procurement, Construction/Installation and commissioning,
  • Very conversant with all relevant codes and standards applicable to Oil & Gas industry project execution and maintenance,
General Requirements:
  • Team player and smart thinker
  • A self-Started with less supervision on what to do
  • Ability to interpret Code and standards accordingly and apply them,
  • Knowledge of recovery plan in terms of delay in delivering quality deliverables,
  • Ability to communicate well at all levels within the Company.
  • Ability to work under pressure and still maintain sanity.
  • Good physical condition, requires walking, climbing, and tolerance to environmental conditions
  • Fluency in English and ability to communicate in equipment supplier’s language.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Rotating Equipment Inspector Location: Nigeria Job Type: Contracts Job Nature: Resident Description
  • Represent the COMPANY in Factory Acceptance Test (FAT) and other relevant integrity tests been conducted by the OEM and act positively and professionally
  • Provide expertise to site team to avoid/resolve quality issues
  • Review Company packages, Contractor procedures, Inspection and Test Plans (ITPs) and other technical and quality documents as required.
  • Ensures that all testing requirements identified in COMPANY specifications are addressed by contractor or supplier.
  • Verify that all testing procedures have been approved and are readily available for implementation. Confirm testing parameters are duly recorded and testing equipment calibrated.
  • Review, Witness and Hold point inspection during procurement and construction in accordance with standard requirements
  • Verify that all rotating equipment systems are built in accordance with the design by carry out visual inspection of the rotating equipment package for overall assembly and installation progress, record and report any defect.
  • Operate inspection / test equipment and record / download inspection data
  • Attend and witness testing associated with Rotating equipment and ancillary systems. Typical tests include radiographic test for fabricated connecting spools, hydrostatic test, alignment checks between coupling and site acceptance test (which includes commissioning) as designated on the approved Inspection Test Plan for the project
  • Assist in Verification, Monitoring and Close-out of Punch List items;
  • Ensure compliance with approved Quality procedures by maintaining accurate rotating records, including protocols and equipment history
  • Perform other tasks as may be assigned by COMPANY
Job Requirements Minimum Qualification:
  • HND or Degree - Mechanical Engineering, Chartered Engineer of relevant Engineering institution or equivalent
  • Professional Experience (number of years): 10-years and above of experience in Rotating equipment inspection, with Project background within Oil & Gas industry. Construction experience is required on Electrical/Instrument installations.
  • Experienced on a wide range of rotating equipment environments (Compressors, Pumps and engines).
  • Must have knowledge of applicable codes and standards of ASME and API
Minimum Professional Certification(s):
  • A member of Nigerian Society of Engineer (NSE) or other international and recognized chartered body
  • COREN Certified
  • Conversant with API - (API 610-Centrifugal Pumps, API 611-General Purpose Steam Turbines, API 614-Lubrication & Shaft Sealing, API 617-Axial/Centrifugal Compressors, API 618-Reciprocating Compressors, API 619-Rotary Type Positive Displacement Compressors for Petroleum, Petrochemical & Natural Gas Industries), ASME & ASNT.
General Requirements:
  • Demonstrates good knowledge and understanding of rotating engineering principles – applies them in some complex and non-routine context.
  • Ability to evaluate process and rotating equipment performance in order to determine production optimization opportunities
  • Ability to communicate well at all levels within the Company.
  • Ability to analyze inspection data trends and make recommendation for inspection level and frequency changes.
  • Good Physical Condition, requires walking, climbing, and tolerance to environmental conditions
  • Must be proficient in common PC software (MS Word; MS Excel; MS Outlook; etc)
  • Fluency in English and ability to communicate in equipment supplier’s language
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Welding Inspector Location: Nigeria Job Type: Contracts Job Nature: Resident Description
  • Ensure proper interpretation of drawings and other documents
  • Perform internal and external inspections to determine if a weldment meets the acceptance criteria of a specific code, standard or document.
  • Plan and witness the Welder Procedure Qualification Test (WQT)
  • Endure and verify conformance of proper Welders Procedure Qualification Record (WPQR) and Welding Procedures Specifications (WPS)
  • Verify the compliance of base metals with the applicable specifications and WQR
  • Assess the adequacy of welding equipment and consumables
  • Appraise joint designs and joint preparations for compliance with drawings and design requirements
  • Verify fit-up, cleanliness and environmental conditions
  • Verify tack-weld and weld quality by checking preheat and inter-pass temperatures and final cleaning
  • Verify welders’ qualification for specific operations
  • Conduct visual examination and other any required NDE
  • Verify cleanliness and weld surface quality prior to welding
  • Oversee NDT examinations and repair activities
  • Verify the proper performance of post-weld heat treatments where necessary
  • Confirm adequate documentation of fabrication/installation and inspection activities
  • Compile and submit data weld quality acceptance or rejection
  • Provide early warning of potential weld quality issues and ensure non-conformances (rejects) are identified and reported to COMPANY.
  • Perform other tasks as may be assigned by COMPANY
Job Requirements
  • HND or Degree - Mechanical or Metallurgical Engineering or related Engineering discipline
  • Professional Experience (number of years): 10-years and above of experience in Welding/Metallurgy inspection, with Project background within Oil & Gas industry.
  • AWS Certified Weld Inspector - CISWIP 3.1 & 3.2
  • Conversant with API, AWS D1.1, ASME (B31.3, B31.4 & B31.8)
  • ASNT level II in VT, UT, MT, PT, RT, etc.)
  • Knowledgeable in reading both isometric and structural drawings
  • Ability to communicate well at all levels within the Company.
  • Ability to analyze inspection data trends and make recommendation for inspection level and frequency changes.
  • Very conversant in electrode management / preservations
  • Experience in Hydrostatic test procedures for pipeline and onshore facilities
  • Good Physical Condition, requires walking, climbing, and tolerance to environmental conditions
  • Must be proficient in common PC software (MS Word; MS Excel; MS Outlook; etc
  • Fluency in English and ability to communicate in equipment supplier’s language
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Material / Receiving Inspector Location: Nigeria Job Type: Contracts Job Nature: Resident Description
  • Carry out material inspection as may be required.
  • Review ITP and provide assurance/control of the quality of the project materials procured or received
  • Manage and execute Materials classification / Coding (to include evaluating and inputting catalogue information plus review and classification of specifications.
  • Ensure no substandard materials enters or used in the project.
  • Receive and action Purchase Order Requests (POR) from Project Engineers and other units of the project.
  • Collects samples for testing and compute findings when in doubt about any project materials.
  • Create and Manage Requisition for Non-Stock Materials in Seplat Supply Chain Management system.
  • Create overall project material receiving Inspection spreadsheet and Monitor their preservation at lay down area as record accordingly
  • Track / Expedite materials through COMPANY Expeditor, transportation and Project Warehouse to end location.
  • Conduct source inspection when the need arises for material vendors and write report accordingly,
  • Advise the Project Warehouse on issue of materials to fabrication contractor and Construction Team.
  • Review all Project MTO’s and raise material requisitions where the need arises,
  • Participate in project meetings and recommend improvements on material management when necessary
Job Requirements Minimum Qualifications:
  • HND or B.Sc / B.Eng Degree in Engineering or Sciences
  • Professional Experience (number of years): Minimum of Ten (10) years and above,
  • Experience in Material inspection, preservation, storage, transit and receiving with project background within Oil & Gas industry.
  • Experience on construction and material management system in the field
Minimum Professional Certification(s):
  • Member Chartered Institute of Warehousing & Material Management (CIWMM) and other relevant professional bodies
  • Very conversant with OEM interface management on material handling and preservations,
General Requirements:
  • A self-starter with less supervision on what to do
  • Ability to communicate well at all levels
  • Must be able to use Microsoft Excel, Word, Outlook and Material Control Systems,
  • Have a wide technical knowledge of various materials categories used in the oil & Gas industry covering all disciplines
  • Ability to estimate material quantity requirements for proper laydown area coverage and management
  • Knowledge of proper functioning, handling, transporting and storing requirements for project materials,
  • Ability to analyze material management for the entire project in terms of Review, witness, approve or recommend.
  • Good physical condition, requires walking, climbing, and tolerance to environmental conditions
  • Fluency in English and ability to communicate in equipment supplier’s language
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Completion / Commissioning & Start-Up Inspector Location: Nigeria Category: Others Job Type: Contracts Job Nature: Other Description
  • Involve in Construction Inspection and Commissioning activities by reviewing As-built (technical) drawings and render support to field Engineers on technical issues relating to completion and commissioning work.
  • Review completed work packages, procedures, Inspection and Test Plans (ITPs) and other technical and quality documents as required.
  • Witness and involve in all pre-commissioning, commissioning and start-up activities of any part of the project.
  • Re-confirm all required tests identified in COMPANY specifications are addressed and signed-off accordingly as part of Pre-commissioning activities.
  • Confirm testing parameters are duly recorded and testing equipment is calibrated.
  • Support field Engineers and Construction team in preparation of pre-commissioning and commissioning activities and translate it to Inspection and Test Plan (ITP),
  • Review all punch items by systems, sub-system and regularly check for completion and close-out of punch items accordingly in line with codes and standards.
  • Record the completion, commissioning and report or raise any defect observed for immediate correction or action to the contractor.
  • Assist in verification, monitoring and close-out of Punch List items.
  • Assist Construction & Engineering team in preparation of Mechanical Completion Certificate, Exceptions List and Ready for Commissioning forms of systems.
Job Requirements
  • HND or B.SC degree in Engineering – Mechanical; Electrical/Instrumentation; Piping and Civil.
  • 10-years and above, Good knowledge in Static and Rotating equipment inspection, with excellent project commissioning background within Gas plant project.
  • Construction experience is required in listing and review of punch items, interface management with OEM and prompt close out of actions items raised.
  • Must have knowledge of interpretation and application of codes & standards e.g ASME, API, ISO etc
  • Member of COREN & NSE
  • ASNT Level II,
  • ISO 9001:2008 or preferably ISO 9001:2015 Auditor certificate.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Community Affairs Officer Location: Nigeria Job Type: Contracts Description
  • Manages community relations programs aligned closely with corporate and project strategies and programs.
  • Has strong community relationships that can be leveraged to protect project execution through initiatives and programs
  • Act as a representative for project at appropriate local gathering and meetings
  • Alert the project whenever a potential risk to life and property is about to occur due to civil unrest
Job Requirements
  • HND or B.Sc in Social Science
  • Excellent people manager
  • Local experience and strategic thinker,
  • Experience in developing and managing community programs to impact positively in the project
  • Ability to foster positive relationships at all levels
  • Sound judgement and initiative.
  • A professional and mature approach
  • A high level of courtesy.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Lead Auditor Location: Nigeria Job Type: Contracts Job Nature: Resident Description
  • Manage the AGPC internal audit program for the certification process,
  • Plan, execute, report and follow-up audits to ensure compliance with relevant EN ISO certification in process,
  • Carry out any required observational audits for all ANOH Gas Plant projects,
  • Manage the route to and maintain self-assurance under integrated management system framework,
  • Advise both site and office team on how to solve non-conformances, follow-up audit responses and ensure effectiveness review and closure
  • Monitor & report certification compliance status,
  • Support and improve the AGPC Management System,
  • Support external certification activities and audits from notified bodies
  • Attend periodic meetings with certification body
  • Report to COMPANY HSSEQ Manager
Job Requirements
  • HND or Degree - in any Engineering or Science related discipline
  • Professional Experience (number of years): 10-years and above of experience in auditing and certification process, with Project background within Oil & Gas industry.
  • Experience in preparing organisation for certification processing from beginning till award of the certificate with COMPANY representative.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Security Advisor Location: Nigeria Job Type: Contracts Description
  • Ability to take security initiative whilst being self-motivated to develop his/her security knowledge and skills
  • Ability to review and build robust security network and alliance building skills
  • Conduct training where necessary by monitoring and reviewing security protocols
  • Facilitate safety in the daily activities of the workplace
  • Identify any potential threats to employee’s physical safety
  • Collaborate with Human Resources to lead or assist with any internal investigations
  • Fight internal security threats as well as external ones
  • Select and implement the most effective systems for protecting staff
  • Interact with all employees to keep them abreast of best security practices
  • Lead educational efforts to empower staff to prevent security threats of any kind
  • Develop, write and publish materials outlining security procedures for the company
  • Report from time to time security updates to the HSSEQ Manager
Job Requirements
  • Degree in Social Sciences, Administration and Business
  • Excellent analytical skills
  • Minimum of 5 years’ experience in security and safety management/logistic
  • Experience of people management
  • Fluent in verbal and written English language
  • Previous similar professional experience or retired security officer
  • Sound understanding of local social and political context and its impact on security, well informed and knowledgeable about global security trend and issues.
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Civil / Structural Inspector Location: Nigeria Job Type: Contracts Description
  • Provide control and monitoring of site early works in surveying the soil and site layout for subsequent civil works.
  • Ability to read drawings, make materials take-off, prepares requests for orders for materials and identify materials on site.
  • Provide expertise to site team to avoid/resolve quality issues relating to civil / structural works.
  • Review Company packages, Contractor procedures, Inspection and Test Plans (ITPs) and other technical and quality documents as required prior to start of construction including early works.
  • Piling works, inspection of post tension suspended slabs, precast walls and structural steel works.
  • Assist in ensuring quality and timely delivery of Civil / Structural scope.
  • Ensures that all civil/structure testing requirements identified in COMPANY specifications are addressed by construction contractor or supplier.
  • Verify that all testing procedures have been approved and readily available on site. Confirm testing parameters are duly recorded and testing equipment is calibrated.
  • Review, witness and Hold Point Inspection during construction in accordance with standard requirement.
  • Verify that all project activities and specifications are built in accordance with the design.
  • Carry out receiving and visual inspection of project activities and materials for overall construction and installation progress, record and report any defect.
  • Conduct site quality walk Inspections of Roads & Locations, Drainage, Helipads, R.C & Structural Steel Buildings, Fence, Water & Sewage Treatment Plants, Equipment Foundations, Storage Tank Foundations, all civil Infrastructure and Community Infrastructure projects, etc.
  • Inspections of quantity measurements, verify quality and variations, follow up change Management process
  • Prepare Quality Control report and submit to the COMPANY
  • Assist in Verification, Monitoring and Close-out of Punch List items;
  • Ensure compliance with internal Quality procedures
Job Requirements
  • HND or Degree - Civil Engineering
  • 10 years and above of experience in Civil/Structural inspection, with project background within Oil & Gas Industry.
  • Must have knowledge of applicable codes and standards in civil/structural engineering
  • A member of professional body e.g COREN, NSE or any other recognized body
  • Very conversant with American Concrete Institute (ACI) and The American Society For Nondestructive Testing (ASNT)
How to Apply Interested and qualified candidates should: Click here to apply online   Job Title: Electrical QA / QC Inspector Location: Nigeria Job Type: Contracts Description
  • Provide expertise to site team to avoid/resolve quality issues.
  • Provide early warning of potential quality issues and ensure non-conformances are identified and reported to COMPANY through regular review, follow-up on corrective actions and update of QA/QC stat
  • Review Company packages, Contractor procedures, Inspection and Test Plans (ITPs) and other technical and quality documents as required to meet COMPANY requirements.
  • Ensures that all testing requirements identified in COMPANY specifications are addressed by construction Contractor or supplier.
  • Verify that all testing procedures have been approved and are on site. Confirm testing parameters are duly recorded and testing equipment are calibrated.
  • Review and witness hold point inspection during construction in accordance with standard requirement.
  • Verify that all electrical systems are built in accordance with the design.
  • Carry out visual inspection of the electrical modules for overall assembly and installation progress.
  • Inspection of cables and cable tray installations, internal & external, junction boxes and panels; inspection of power and control cables installation to ensure compliance with the applicable codes and standar
  • Inspection of HVAC systems and ducting installations.
  • Operate inspection/test equipment and record/download inspection data.
  • Attend and witness testing associated with electrical equipment and systems as required by design and approved Inspection Test Plan for the project.
  • Assist in Verification, Witnessing, Monitoring and Close-out of Punch List items;
  • Perform quality audit (spot checks) to verify work activities are in compliance with approved Quality procedures.
  • Represent Company and Service Contractor in a positive and professional manner.
  • Witness system FAT and SAT as may be required.
  • Ensure Contractor’s documentation conform and are compiled progressively as
  • Carry out daily surveillance reporting and submission of weekly report of Contractor’s work.
  • Provide general QA/QC direction to Company on QA/QC related
Job Requirements
  • HND or Degree in Electrical Engineering.
  • Professional Experience: 10 years and above of experience in Electrical inspection with Project background within Oil & Gas industry. Construction experience is required on Electrical installations.
  • Experience on construction yard in Construction Contractor team is required.  Proficiency in using Microsoft Office Suite (Word, Excel and Outlook).
  • Must have knowledge of applicable Local and International Codes and Standards (e.g. IEC, NFPA, UL, ANSI, IEE Regulations et), as applicable in the oil/gas industry.
  • Good understanding of design of electrical systems of oil and gas processing facilities
  • MNSE, MNIEEE or MIEEE; COREN (Added advantage);
  • International/professional Certifications e.g CEI, etc.
How to Apply Interested and qualified candidates should: Click here to apply online   Deadline: 4th November, 2019.